Recycling information for Hypertherm customers and recyclers
Under the Waste Electrical and Electronic Equipment (WEEE) Directive and implementing regulations, when customers buy new electrical and electronic equipment from Hypertherm they are entitled to:
- Send old equipment for recycling on a one-for-one, like-for-like basis (this varies depending on the country)
- Send the new equipment back for recycling when this ultimately becomes waste
Instructions to both customers and recyclers/treatment facilities wishing to obtain disassembly information will be provided by sending an e-mail to email@example.com.
What to do with your used Hypertherm products
Elimination and reduction of waste is the foundation of a good approach to end-of-life equipment management.
If you have a Hypertherm power system that you are done using, we encourage you to determine the most sustainable path for it. At Hypertherm, we design our products to last a long time. This is the first step in eliminating waste. We also design our products to be as lightweight and to use as few components as possible. All of this eliminates material at the source, before it can even become waste.
Below are options for your Hypertherm products listed from best to worst for the environment.
Reducing waste is even better than reuse or recycling. Please consider whether you really need to get rid of your system, or whether you might extend its life through:
- Repairs or upgrades – can be lower cost for you, and less resource intensive. You could upgrade the torch to get the increased performance you need, repair just the components that are not functioning, or upgrade the software to take advantage of Hypertherm’s automation technology.
- Preventive maintainence will help your system last longer. Take a class from Hypertherm Cutting Institute and learn about ways to use your existing equipment more effectively.
After an extremely long life with you, the next best thing for your system is to serve its highest and best use, as cutting equipment, with someone else. Can you resell it? Could you give it away? If it is not serving your needs, maybe it could serve someone else.
Another option is to save the functioning components that you might put to use again as spare parts for repairing other equipment.
The final option is to scrap your system. The good news is that your system is highly recyclable and it should be low cost, free, or will bring in revenue, to recycle it. Follow these steps to scrap your system or watch videos below for instructions.
- Unplug, de-energize, and let it sit for 10 minutes so that capacitors discharge. Read the Safety and Compliance manual. Use safety glasses and gloves. Remove cover.
- Remove the printed circuit boards. These should be sent to an R2 or Rios certified e-waste recycler. If sent to these experts, all components will be 100% recycled.
- Search for e-waste facilities by zip code – While all of these are not certified, they will recycle your e-waste.
For CNCs, send the entire unit to an R2 Rios Certified e-waste recycler. Do not attempt to remove the CCFL lamps from the screen. However the screen is easy to remove in its entirety and can be reused as a monitor, plug and play. The circuit boards and chips are valuable enough that you should not have to pay to dispose of them. If you must send the system to your regular scrap vendor where it will end up shredded, please remove the screen and lithium battery first.
Disassemble your system to get the highest scrap values. No special tools are needed. Before you spend the time, check to see if a local e-waste recycler will pay you more for separated materials or check to see if your facility already has separate collection for aluminum or copper.
Full tear down
This is the easiest path. You can put the whole system, without the e-waste components such as printed circuit boards, into your mixed metal scrap bin. Please point out to your scrap vendor that there are valuable components within the system, such as a pure aluminum heatsink, lots of copper on the transformer, mixed copper and aluminum in the cold plate (radiator), and potentially reusable fans, motors, pumps, or air regulators.
Depending on your vendor contract, the least you will get is $0.10/lb. for the system, or approximately $70 for an HPR® or MAXPRO and $5 for a light industrial or Powermax system.
Scroll through the videos below of various stages of the MaxPro® and the EDGE® Pro CNC being disassembled. Video titles will appear when video is clicked.
EDGE Pro – Screen, front panels, circuit boards
EDGE Pro – Door, side panels, fan
EDGE Pro - Circuit boards, wires
EDGE Pro - Internal frame, fans
EDGE Pro - Internal frame, back boards
EDGE Pro - Heatsink, back panel
EDGE Pro - Wires
EDGE Pro - Lower back ports, connectors
EDGE Pro - Chips, processor, fan, screen
MAXPRO - Control panel, large fan, resistors
MAXPRO - Coolant tank, IGBT, back box
MAXPRO - Water filter, air regulator
MAXPRO - Capacitors, diodes, coolant hose
MAXPRO - Capacitors, transformers, inductors
MAXPRO - Motor cables, transformers
MAXPRO - Vertical panel
MAXPRO - Transformer, motor