The MAX200 continues Hypertherm's tradition of combining advanced technology and superior quality to deliver operating advantages that are unmatched in the industry.
Operating Data
- Production cutting capacity (piercing)
- mild steel 1" (25 mm) - Maximum pierce capacity
- mild steel 1" (25 mm) - Maximum cutting capacity (edge start)
- mild steel 2" (50 mm)
Related products
Related links
Share this:
Entry-level oxygen cutting system, great for often-changing cutting requirements and production schedules. A proven production cutting system with an attractive initial capital cost.
| Capacity Mild Steel |
Dross free Production (pierce) Severence (edge starts) |
25 mm (1") 25 mm (1") 50 mm (2") |
|---|---|---|
| Stainless Steel |
Production
(pierce) Severence (edge starts) |
25 mm (1") 50 mm (2") |
| Aluminum |
Production (pierce) Severence (edge starts) |
25 mm (1") 50 mm (2") |
| Speed* (Mild steel) |
Optimum quality |
12 mm (1/2") 2159 mm/m (85 ipm) |
| Cut angle | ISO 9013 range** | 4-5 |
| Weldability | Ready to weld |
|
| Process gases by material (Plasma/shield) |
Mild steel Stainless steel Aluminum |
Air/Air,
O2/Air, N2, CO2 Air/Air, N2/Air, N2/CO2, H35/N2 Air/Air, N2/Air, N2/CO2, H35/N2 |
| Process amps | Not all processes available for all materials |
40-200 beveling (200) |
* Note: Take care in comparison: competitors often show maximum cutting speeds rather than speeds that deliver the best cuts, as shown above. Cut speeds listed above deliver best cut quality, but cut speeds can be up to 50% faster.
** ISO 9013 is a standard that defines cut quality of thermally cut parts. The lower the range (range 1 is the lowest), the smaller the angle on the cut face. Cut angle in range 4 is better than in range 5.
MAX200s Hand Torch Consumables
| The MAX200 Advantage 200 amp, 30 kw power output delivers heavy-duty cutting capacity up to 2 inches (50 mm) thick on most metals; typical cutting speeds greatly exceed oxyfuel or other methods. 100% duty cycle at full power keeps you cutting - all day long. Adjustable power output from 40 to 200 amps lets the operator precisely match power to cutting requirements. A state-of-the-art transistorized power supply maintains constant output current regardless of variations in input voltages or torch-to-work distances, ensuring clean, square cuts throughout the cutting range. Max200's dual gas system - plasma and shield - allows you to run on Air/Air, 02/Air, N2/Air, N2/CO2, Ar-H2N2 or other combinations for optimal results on all metals and conditions. | The MAX200's patented shielded torch front-end practically eliminates the possibility of double arcing, greatly enhancing piercing capabilities and extending consumable parts life. The water-cooled torch provides maximum cooling, another factor behind MAX200's long consumable parts life; the cooling system is built into the power supply for exceptional convenience. The MAX200 can be used on cutting machines or for hand-held applications. A machine motion delay control comes built into every system. Optional Torch Height Control (THC) and inductive Initial Height Sensing (IHS) are available for mahcine use. New consumables, an optional extended torch and heat shield, optimize the MAX200 for gouging applications. | A full set of easy-to-read indicator/diagnostic lights monitor the status of external door panels, transformer and chopper temperature, coolant level, plasma and shield gas pressure, coolant temperature, and coolant flow, greatly simplifying troubleshooting. Extended leads up to 150'(45m) are available for both hand-held and mechanized systems for added flexibility. Safety interlocks are built in, ensuring maximum operator safety. MAX200 comes equipped with casters for easy wheeling, and there is a lifting eye located at the balance point for use with cranes. A full two-year warranty on the power supply and one-year coverage on the torch backs up Hypertherm's quality commitment. |
- Videos
- Hypertherm at SEMA Trade Show (19 MB) Watch video
- Hypertherm: 40 years of innovation (60 MB) Watch video
- Integrated Plasma Cutting Solutions (47 MB) Watch video
- Optimizing Your Plasma Operation (51 MB) Watch video
- World's Greatest TV program (17 MB) Watch video
- System Sales Tools (None Available)
- None Available
- Customer stories
- Application: MAX200 Mounted on Whitney Punch Press for the OEM Manufacturing Industry (797 KB) Download
- Product news (None Available)
- None Available
- Photos (None Available)
- None Available
- Logos (None Available)
- None Available
- Advertisements (None Available)
- None Available
- Service Information
- MAX200 Check Valve Retrofit (505 KB) Download
- MAX200 Plasma Gas Gauge (194 KB) Download
- MAX200 Service Manual (17 MB) Download
- MAX200 Underwater Torch Supplement (3 MB) Download
- MAX200 Wheel Installation (245 KB) Download
- MAX200/THC2 Torch Height Control Retrofit (512 KB) Download
- Max200 Work Lead Repositioning (1 MB) Download
